Arcade Parts Control Panel

Concave Design Microswitch reliability tested to 10,000,000 cycles. Vertical attached microswitch with standard 0. 187" (4. 8mm) terminals. 28mm H...

Convent One Piece Design, not super long like other style buttons. 28mm Screw Type If you need encoder wires get them HERE

Convert your Japanese style ball top joystick to the more recognized American style. This will work on: Sanwa Zippy Arcade1Up AtGames Legends  

Replaces Sanwa Part Number:GT-Y This GT-Y plate is compatible with the Sanwa JLF series joysticks: JLF-TP-8YT(-SK) JLF-TP-8Y(-SK) JLF-TP-8S...

Microswitch Reliability Tested To 10,000,000 Cycles Vertical Attached Microswitch With Standard 0.187" (4.8mm) Terminals 12V or 5V. If you need en...

The 4lb tension spring can be used as a replacement for the existing spring found in the Sanwa JLF series of Joysticks. Modding your Sanwa JLF joys...

Plastic push button with translucent bezel Black center for Eclipse look LED holder .250" terminal size Fits wood or metal control panels Pushbu...

One End is a Standard 0.187" (4.8mm) Terminals Other End is a 2 Pin JST Commonly used on Encoders and Arcade1Up 12 Jumpers Per Pack

Runs on 5 volt. Button connection Size: 0.110 (same size as standard sanwa) We offer the led harness for these in our store! Convent One Piece Des...

Arcade Quality Buttons! Microswitches included inside the Button! fits in most Hori and MadCatz joysticks Microswitch reliability tested ...

6MM Ball Thread.

The 2lb tension spring can be used as a replacement for the existing spring found in the Sanwa JLF series of Joysticks. Modding your Sanwa JLF joys...

Fits Small 0.0110" (2.8mm) TerminalsMultiple Lengths Available 12 Packs or Singles

25¢ Push For Credit" graphic embedded inside the buttonMicro switch Reliability Rated at 10,000,000 cycles Package Contents: 25¢ Push Button LED 1...

These are replacement bulbs for our Chrome and Eclipse buttons. They will work with either 5v or 12v. Sold each.

Arcade Encoder For Sanwa Style (Complete w/Cables) Fits small 0.110" (2.8mm) Terminals and Sanwa 5 Pin Joystick1 - Arcade Encoder1 - USB Cable13 - ...

12mm Size button Momentary - Does not stay pressed down once released requires a 0.50" hole 0.110 terminal size 3A /125VAC 1.5A/250VAC

Arcade Encoder For Happs Style (complete w/Cables) - Fits Standard 0.187" (4.8mm) Terminals1 - Arcade Encoder1 - USB cable12 - Happs Style Jumpers

Shaft Diameter: 9mm Adds 15mm of Height Compatiable With Sanwa, Zippy, JS19 and other Joysticks That Are 9mm.

Use this cable to hook a Sanwa joystick into a standard 0.187 terminal end jamma hanress. Simply plug the U D L R into the correct slots and hook t...

Feature: Hard plastic, long lifespan. High quality 12v LED standard Illuminated arcade push buttons. Will work on wood or metal control panels.S...

The 6lb tension spring can be used as a replacement for the existing spring found in the Sanwa JLF series of Joysticks. Modding your Sanwa JLF joys...

Specification: Used to convert a PS2 trackball to USB. USB plug and play compatible. Compatible with USB 3.0, USB 2.0, USB 1.1 ports. Support Wind...

Specifications: USB 2.0 Speeds Total Cable length: approx. 1 m / 3.3 ft Flush mounting 28mm hole Connector: USB A-type male to USB A-type female